If seals start opening after a switch to recycled corrugated cartons, inspect the surface being bonded before changing adhesives. A different liner, colder board, short open time or weak compression can each produce a failed seal. Compare failed cartons with sealed cartons from the previous board lot under the same line conditions.
The word “recycled” alone does not identify the bonding problem. The useful evidence is the actual liner surface, where the adhesive ends up when the seal is opened, and when the carton fails.
What changed on the bonding surface?
The liner finish can change even when the carton still looks like brown corrugated board. Check the liner that receives the bead and the liner that closes onto it. Printed, coated and uncoated areas should be treated as distinct bonding surfaces.
Keep samples from the old and new board lots. Mark the glue area and compare visible finish, loose surface fibers and temperature at the line. If the bead now lands on a coating or printed area, tell the adhesive supplier exactly which surface is being bonded.
Where does the adhesive stay when a seal fails?
The adhesive’s location on the opened flaps helps distinguish poor transfer from a bond that split before setting. Open several failed cartons and look at both flaps. Adhesive left cleanly on one flap points toward poor contact or wetting of the other surface.
A bead split between both flaps points to a cohesive failure. Check adhesive amount, compression and whether the carton moved before the bond had set.
Fiber torn from the liner indicates that the board failed before the adhesive joint released at that spot. Record the pattern across several cartons rather than judging one tear. If failure appears only on the new board, include both board samples in the investigation.
How can you tell whether the bead stays open until compression?
Compare the time from bead application to flap compression with the adhesive’s open time under your line conditions. The adhesive must remain able to wet the second flap during that interval. A cold board can shorten the effective working time by cooling the bead sooner.
Measure that interval at normal production speed and check the current adhesive data sheet. If the bead has already cooled past its useful open time before the flaps meet, changing compression pressure alone will not restore wetting. Confirm actual adhesive temperature at the applicator before considering a grade with a different open time.
What does the compressed bead reveal?
The compressed bead shows whether the flaps made contact across the bond area. Compare bead shape before and after compression. A rounded bead or patchy transfer points to inconsistent contact; check flap alignment, compression pressure and compression time at production speed.
Watch when cartons open. A flap that springs back as compression ends may need more initial hold or a faster-setting adhesive. A carton that opens later during handling needs a separate check against its storage and shipping conditions.
Will applying more hot melt solve the failure?
No, not unless the current bead leaves part of the intended bond area uncovered. First verify bead placement and transfer. Adding adhesive can slow setting and allow a carton to open as it leaves compression.
If coverage is inadequate, adjust the pattern within the equipment and adhesive specifications, then check the finished seal. Robatech’s application nozzle guidance explains why nozzle diameter, adhesive amount, open time and pressing time must align. If coverage is already consistent, use the failure pattern to decide whether the next trial should address open time, compression or bonding to the new liner.
How should you compare adhesive candidates on recycled corrugated cartons?
Run each candidate on the same recycled board lot, carton format and line speed. Record applicator temperature, bead pattern, application-to-compression interval and compression settings. Inspect seals immediately after compression and after normal handling; include the expected storage temperature if it differs from the production floor.
Keep an old-board control where possible. It helps show whether the failure follows the board change or persists across both stocks. The packaging hot melt adhesive range provides a starting point for discussing a trial, but suitability for your recycled liner needs a line test.
The EVA hot melt adhesive and APAO hot melt adhesive collections show candidate chemistries. Neither establishes suitability for a particular recycled liner without a line trial.
Send both board samples, failed-seal photos and these line records when requesting a matching grade. Request a current technical data sheet for any proposed grade and compare seal performance under the same conditions.







